產品詳情
現場墻體傳熱系數測定儀生產廠家
無線式墻體傳熱系數現場檢測儀（現場墻體傳熱系數測定儀）
一、產品概述
WH-2無線式建筑圍護傳熱系數現場檢測儀是依據GB/T23483-2009《建筑物圍護結構傳熱系數及采暖供熱量檢測方法》、JGJ/T 132-2009《居住建筑節能檢驗標準》、JGJ/T 357-2015《圍護結構傳熱系數現場檢測技術規程》等標準采用智能觸摸屏和物聯網模塊研制開發的高精度、低功耗的新一代檢測儀器。
該檢測儀是通過控制熱箱內溫度，人為造成試件兩側溫差，在相對穩態條件下進行測量，從而提高總體測試精度。該檢測儀適用于建筑圍護結構傳熱系數現場檢測和實驗室檢測。通過采集試件表面的熱流密度、內外表面溫度之差計算出試件的熱阻值。最后再算出傳熱系數。
優勢特點：
1、具有體積小、精度高、操作方便等特點。
2、在溫度采集方式上，特別是外表面溫度的采集，由于受建筑結構的影響，通常需要進行長距離的布線，施工.麻煩且費用高。本檢測儀對于外墻溫度的采集采用無線通訊方式，去掉溫度傳感器與檢測采集儀的線纜連接，從而簡化了施工難度，避免了由于通訊線纜帶來的穿墻打洞布線等的麻煩，使檢測變得更加方便快捷。
3、實現通信距離zui高可達150米（室內）或300米（空曠），在室內可以隔墻傳輸10～15層左右；
4、采用了高智能低功耗的無線通訊技術，提高了電池的使用壽命，根據不同的使用情況電池壽命可達2~3年；
5、具有斷電保持的功能。更換電池不會影響試驗。更換電池后儀器自動進行數據傳輸，繼續完成試驗過程。
二、技術參數：
1.熱箱控溫范圍：25～50℃；
測量精度：0.25℃；
控溫波動范圍：土0.2℃；
2.熱流密度：量程范圍：0-±15mV；
分辨率：0.001 mV；
測量準確度：<0.01 mV
流密度值由選配的熱流計決定；
3.控制箱自動記錄數據，采樣時間可設置；
4.外墻無線溫度采集模塊與控制箱之間采用無線通訊，通訊最大距離150m（室內）或300m（空曠）；
5.配帶動力：交流220V，功率：1000W.有良好的接地；
6.熱箱設備外形尺寸：長×寬×高(mm)=1320×1320×300mm。
現場墻體傳熱系數測定儀生產廠家
Wireless On-site Wall Heat Transfer Coefficient Tester
I. Product Overview
The WH-2 Wireless Building Envelope Heat Transfer Coefficient Tester is a new generation of high-precision, low-power testing instrument developed in accordance with standards such as GB/T 23483-2009 Test Methods for Heat Transfer Coefficient of Building Envelopes and Heating Supply, JGJ/T 132-2009 Energy Efficiency Inspection Standard for Residential Buildings, and JGJ/T 357-2015 Technical Specification for On-site Detection of Heat Transfer Coefficient of Building Envelopes. It utilizes an intelligent touch screen and IoT modules.
The tester artificially creates a temperature difference across the specimen by controlling the temperature inside the hot box. Measurements are taken under relatively steady-state conditions to ensure high testing accuracy. It is suitable for both on-site detection of building envelope heat transfer coefficients and laboratory testing. The instrument calculates the thermal resistance of the specimen by collecting the heat flux density and the temperature difference between the inner and outer surfaces, and subsequently derives the heat transfer coefficient.
Advantages & Features
-
Compact & Precise: Features a small footprint, high accuracy, and user-friendly operation.
-
Wireless Innovation: Traditional bs require extensive wiring through walls for exterior surface temperature measurement, which is costly and labor-intensive. This device uses wireless communication for exterior wall temperature collection, eliminating the need for cable connections, simplifying construction, and avoiding the hassle of drilling holes.
-
Long-Range Communication: Achieves a communication distance of up to 150 meters indoors (capable of penetrating 10–15 walls) or 300 meters in open areas.
-
Low Power Consumption: Utilizes intelligent low-power wireless technology, extending battery life to 2–3 years depending on usage.
-
Power Failure Protection: Features data retention during power outages. Battery replacement does not interrupt the test; the instrument automatically resumes data transmission and continues the testing process upon battery replacement.
