產品詳情
The Divider Type Petroleum Storagetank Central Drainage Device
The Divider Type Petroleum Storagetank Central Drainage Device has the structure of steel tube folding and composite bl hoses. The steel tube is 20# seamless steel pipe,The inner and outer surface spray coating epoxy conducting electrostatic anti-corrosion coatings. There are three layers structure in the composite hoses, The innermost material is sealed stainless steel Bellows; It’s available in 316L stainless steel for corrosion resistance. The material of the middle is NBR, and Vulcanization in the surface of the stainless steel Bellows, which make the composite hose have a good perbance of double sealing. Only when the Bellows and their vulcanizing surface layer are in the same spot , sulfide leakage can make composite Hoses to lose effectiveness. The outmost layer is 304 stainless steel wire braid, which is used to protect the main body of the tube. The top hinge is of universal joint structure, it enables a range of movement in circumferential direction and overcome the strong stress caused by the circumferential movement of the floating tray. The underneath hinge is of dual hinge structure, which can only move up and down. It makes the central drainage device have a constant move path. Gear pair is used in the jount of two straight tubes of the central drainage device. It makes the two straight tubes stay the same in the angle, in the meantime, it also restrains the four composite hoses stay the same in the debation.
1、The MainCharacteristics:
1.1 There is no dynamic seal problem. The drainage device has overcomed the problem, that the revolving joints structure of dynamic seal is easily be abraded and leakage.
1.2 The cardan joint structure that can move in circumferential direct and up and down used in the joint of steel tube and floating roof, which has overcomed the strong stress caused by the circumferential movement of the floating tray.
1.3 Having a good stress layout , ensure the Device of drainage system in the Non-Stress status work.
1.4 The underneath hinge structure is dual hinges structure,It runs smoothly and has a constant move path while working.
1.5 The Gear pair structure makes the two straight tubes stay the same in the angle , in the meantime, it also restrains the four composite hoses stay the same in the debation .It extended the working life of the composite hoses.
1.6 Bending radius of the composite hoses was designed by 15 times diameter
4、儲罐規格與排水裝置性能表
StoragetankSpecification and Drainage Device Perbance Table
儲罐Storagetank | 容積(萬m3) Cubage (Ten thousandm3) | 0.1 | 0.2 | 0.3 | 0.5 | 1 | 2 | 3 | 5 | 10 | 12.5 | 15 |
直徑 Diameter ( m ) | 12 | 14.5 | 16.5 | 22 | 28.5 | 40.5 | 46 | 60 | 80 | 84.5 | 94 （100） | |
罐高Height of Storagetank (m) | 9.52 | 12.69 | 14.27 | 15.85 | 19.35 | 21.8 | 23.9 | 24（21.4） | ||||
中央排水裝置Central Drainage Device | 單排水通經Single DrainageDiameter (mm) | 20 | 80 | 100 | 125 | 150 | ||||||
雙排水通經 Double DrainageDiameter (mm) | 100 | 200 | 200 | 250 | ||||||||
位移高度Displacement Height (m) | 10 | 13 | 14.5 | 14.5 | 16 | 16 | 20 | 20 | 22 | 24 | ||
公稱壓力 Nominal Pressure (Mpa) | 1.0 | |||||||||||
液壓試驗Hydraulic Test (MPa) | 1.5 | |||||||||||
氣壓試驗 Pneumatic Test (MPa) | 1.0 | |||||||||||
爆破壓力 Bursting Pressure (MPa) | ≥3.0 | |||||||||||
The drain-pipe diameter of this Central Drainage Device is DN100-200 mm, and this device can be used in the tank of 2000M3-150000M3, it can also withstand 1.6 MPa working pressure and 120℃ working temperature. The service life is two overhaul periods. For other Devices’ structure, any damage will cause the whole device’s invalidation. But this Devices wearing place has the composite bl hoses, when the Storagetank is overhauled in the schedule time, which can be replaced quite conveniently.
浙江樂鼎波紋管有限公司（原名浙江樂清市金屬軟管廠），創建于1992年，占地面積11720平方米，座落于樂清市南塘鎮，地處104國道旁，交通便捷，環境優美，距國家級旅游勝地雁蕩山僅幾里之遙。 公司注冊資金1018萬元，年產值3000萬元，是國家化工部指定產AAA級資信企業
